Awesome Baozam - User contributions [en]

Combie v4

2021-09-15T11:46:34Z

Monster:

[[File:Combie_board_v4.1.png|800px|thumb|Board]]

This is mono metal-magnet detector with Wi-Fi internet connections.

== WiFi Setup ==
All Baozam devices use the same [[WiFi Setup]] procedure. The difference is in where the setup button is placed and how it looks. The combie ''WiFi setup'' button is marked by red at Figure.
* [[WiFi Setup|Common Baozam device WiFi setup procedure]]

== Device tuning ==
All Baozam devices have common interface for tuning via the Internet.
Please, read details at [[Device tuning via the baozam.net website]] page.

This device can also be configured through the USB with the use of [[Local tuner software]].

== Individual parts configuration ==
* [[Magnet detector configuration v4]]
* [[Metal detector configuration v4]]
* [[EXTIN configuration v4]]
* [[Indication configuration v4]]

[[Category:Combie-Shop|*]]

File:Tuner v3 1 (1).rar

2019-09-18T16:34:19Z

Monster:

Main Page

2019-09-18T16:04:37Z

Monster: /* Common procedures */

== Devices ==
* [[Acousto-magnetic EAS systems]]
* [[Iridium mono 2k IR 1040 06 V4|Iridium mono RF systems]]
* [[Bidirectional pass counters]]
* [[Combies|Combies or Combined Magnet Metal detection systems ]]
* [[Magnet detector]]

== Common procedures ==
* [[Baozam Usage]]
* [[WiFi Setup Common|WiFi setup procedures]]
* [[Device tuning via the baozam.net website]]
* [[Data export]]
* [[Baozam Howto | Baozam How To]]

== Miscellaneous ==
* [[CMD:000|Manual List of known commands]]
* [{{fullurl:Special:Allpages|namespace=3000}} List of described commands]
* [[Parameter types]]

[[uk:Головна сторінка]]
[[ru:Заглавная_страница]]

MagnetGuard V2 - Initial configuration of the system

2019-02-06T09:45:23Z

Monster: /* Connecting the sensors with the central unit */

== Initial configuration ==
While in some cases sensors and central units may contain the configuration information used for factory testing, it is necessary to erase (reset) them before new installation.
=== Reseting of the sensor ===
• unscrew the two screws on the back cover of the sensor, remove the cover 
• remove the battery from the battery compartment 
• press together buttons 1 and 2 (see [[MagnetGuard V2 - The Sensor| the sensor ]]) and keeping them down insert the battery. Wait till the sensor will switch to active mode (see [[MagnetGuard V2 - The Sensor| the sensor ]]) 
• release buttons 1 and 2, indicator LEDs 1 and 2 will flash 
• reboot the sensor by removing and inserting the battery and wait till it is in active mode 
=== Reseting of the central unit ===
• unplug the power supply of the central unit 
• wait for about 15 seconds to fully discharge the internal electrical circuits 
• press the button «Connect» (see [[MagnetGuard V2 - The Central Unit| the central unit ]]) and keeping it down plug the power supply 
• the central unit confirms the erasing process by lighting up the yellow LED «PAIR» 
=== Connecting the sensors with the central unit ===
• make sure that the sensor and central unit are switched on (central unit with power supply, sensor with battery inserted) and the back cover is removed from the sensor 
• locate previously reseted sensor and central unit at a distance less than 50 cm between them 
• press the button «Connect» (see [[MagnetGuard V2 - The Central Unit| the central unit ]]) on the central unit - yellow LED «PAIR» should start to blink 
• press together both buttons 1 and 2 (see [[MagnetGuard V2 - The Sensor| the sensor ]]) on the sensor board – the pairing process will start and both LEDs 1 and 2 will light up 
• in the event of successful connection performance the yellow LED on the central unit and both sensor LED’s will turn off 
• make tests with a detacher close to the sensor to make sure it will be detected. Corresponding red LED (1 - 10) on the central unit should light up for 10 seconds. 
• the central unit assigns the indication channel number (red LED’s from 1 to 10) to the sensors automatically in order of registration process (i.е. the first registered sensor will be assigned to channel 1, the second sensor to channel 2 etc.).

IMPORTANT! To prevent possible wiretapping of the configuration information the registration process and the connection performance between sensor and central unit is to be carried out at minimum wireless communication. Therefore the distance between the sensor and central unit should be minimal.

Magnet detector configuration v1

2019-01-11T09:57:51Z

Monster: /* Parameters description */

__TOC__
=== General functionality description ===

Device can works in configuration of two separate dual (two sensors) magnet detectors. So device has two connectors for magnet sensors cables (each cable connect two magnet sensors).

Device has two separate group of parameters (Magnet 1 and Magnet 2) for tuning dual magnet detectors and it has four groups of parameters (MS 1..4) for sensor tuning.
These parameter groups allow you to configure the detection of magnets by two dual magnet detectors separately.

The system responds to a change in the magnetic field in the range of the sensors. If reaction correspond to magnet detection settings it consider as alarm. So internal state is changing to alarm state, alarm counter is incrementing, common system buzzer is switching-on ("fast beeps"), external LEDs (1, 3) indication is switching-on.
After a short time when magnetic field is not changing (magnet is not moving) or it is out of the detection area, if reaction is less then magnet detection settings it consider as end of alarm. So internal state is changing to normal state, common system buzzer and corresponded external LEDs indication are switching-off.

Also each magnet detectors can use two-sensor measurements for filtering false alarms caused by "far located strong magnet" (urban transport, elevators), impulse disturbances (electrical drive of sliding doors, power converters).

At the same time, each magnet detectors can use corresponded metal detector data for correction the magnet detection.
These functions are intended for detecting magnets when used on an object (for example, cash registers of hypermarkets), in the area of operation of a system of trolleys with an iron structure, since iron has the properties of a magnet.

The device can send information about the number of alarms for a period or a message about the operation based state variables to account the statistics of the alarms and for synchronization with the video surveillance systems.

=== Parameters description ===
[[File:Combie manual magnetdet 2.2.png|thumb|right|450px|Fig. 1: shows an example of the change in the state of the state in time, depending on the indicator value (dV) and the influence of the tuning parameters (th, th in delay, th out delay)]]

'''Parameters groups MS x''' for magnet sensor tuning.
* '''dV''' - the response of the system over the magnetic field
* '''th''' - sensitivity detection setting. The parameter values are selected based on the noise level (0.25 ... 10.0)
* '''Babs''' - current level of field strength in mGs measured by the sensor
* '''bsize''' - the size of the history buffer for analysis (100 - corresponds to 1 second maximum value 250, minimum 10)
* '''window''' - analysis window (50 - corresponds to 0.5 sec). The '''''bsize''''' / '''''window''''' ratio affects the speed sensitivity of the magnet
* '''in delay''' & '''out delay''' - time setting for detection when '''''dV''''' is exceeded above '''''th''''' and at detection loss at '''''dV''''' is less than '''''th'''''
* '''state''' - the state of detection of the magnet
* '''alarm counter''' - the lifetime magnet sensor events counter.
See figure 1 for details.

'''Parameters groups Magnet x''' for magnet detector tuning.

* '''dV''' - the overall response of the system to the magnetic field with compensation
* '''th''' - sensitivity detection setting. The parameter values are selected based on the noise level (0.25 ... 10.0)
* '''in delay''' & '''out delay''' - time setting for detection when '''''dV''''' is exceeded above '''''th''''' and at detection loss at '''''dV''''' is less than '''''th'''''
* '''state''' - the state of detection of the magnet
* '''alarm counter''' - the lifetime magnet sensor events counter.
* '''algo''' - the detection algo.
0 - Simple magnet detector. Detection is depended only on sensors sensitivity settings (MS 1, 2 for Magnet 1 MS 3, 4 for Magnet 2). When one of two sensors detects magnet it's consider as magnet detector alarm. '''dV''' is not affected in this mode
1, 2 - Dual magnet detector in gain sense mode 1 and 2. The main detection variable '''dV''' is calculated as a sum of each sensors responses without/with sign of values considering.
10, 11 - Dual magnet detector in magnet filter mode 1 and 2. The main detection variable '''dV''' is calculated as a delta sensors responses without/with sensors space orientation considering.
20, 21 - Dual magnet detector in metal filter mode 1 and 2. The main detection variable '''dV''' is calculated as a sensors responses with metal detector data compensations. In this mode is need to tune parameters from group '''Magnet x adv'''

'''Parameters groups Magnet x adv''' for tuning magnet detector in metal filter modes .
* '''tau''' - the parameter of calculating the rate of change of the metal response.
* '''win magnet''' - the size of the history buffer (5 - corresponds to 0.05 sec) for the analysis of changes in the magnetic field
* '''win metal''' - the size of the history buffer (10 - corresponds to 0.1 sec) for analysis of changes during the movement of metal
* '''AB magnet th''', '''AB metal th''' - set ranges of dV for magnet alarm blocking
* '''K-magnet-2''' - the parameter of taking into account the rate of change of the magnetic field
* '''K-metal''', '''K-metal-2''' - the parameters of accounting for changes and the rate of change during the movement of the metal

=== Setup procedure ===

1. To assess the level of the magnet's influence, use the variable '''''dV''''', which should be [[Device_tuning_via_the_baozam.net_website#Monitoring|chosen for monitoring]].
The system should tuned to the best sensitivity when detecting moving magnets using the parameters '''''th''''', '''''bsize''''', '''''window''''', '''''in delay''''' / '''''out delay''''', taking into account the noise level.

The magnet detector is evaluated using the state and counter variables, as well as based on the external LED indication.

The range of detection depends on the level of magnetic induction of the magnet, the direction of its magnetic field and the speed of motion. For tuning, you can use a standard magnetic puller with an induction of 6-10,000 Gauss.

After the settings, save the settings.

2. False triggering in some cases can be caused by impulse and constant interference at the installation site, for example, when the sliding doors (especially with the DC collector drive) are close (<2 m), when power consumers switch on/off the power line (depends on Parameters of the mains), with close proximity (<0.5 m) of mains power lines, with close location (<25 m) of transport routes (metro, tram, parking). The detuning from false alarms can be performed by a load of sensitivity (increase in '''''th'''''), as well as an increase in the delay in triggering '''''in delay'''''.

3. For false alarm filtering select corresponded '''algo''' value from '''Magnet x''' group , use the variable '''''dV''''', which should be [[Device_tuning_via_the_baozam.net_website#Monitoring|chosen for monitoring]].
The system should tuned to the best sensitivity when detecting moving magnets using the parameters '''''th''''', '''''in delay''''' / '''''out delay''''', taking into account the noise level.

[[Category:Combie-Shop]]

Register your devices

2018-12-06T12:58:24Z

Monster: /* Device registration */

==Device registration==
Once you have already successfully created your '''Baozam account''', it's time to add your first '''Baozam device'''.
The '''registration procedure''' for all '''Baozam devices''' is the same. At the production stage each '''Baozam device''' is registered in the device database. Each device is already fully functional and can work with cloud services. But it still does not have an '''owner''' and '''nobody can access''' to its data and control functions.
A link between the '''Baozam device''' and its '''owner''' is provided with a '''Baozam card''' that is attached to each device. This card has a number and PIN-code by entering which the user declares himself as the '''owner''' of the device and binds the device with his account. '''Attention! The card can be used only once.''' 
===Registration procedure:===
*Log in into your '''Baozam account''' on baozam.net
*In main menu choose '''Configuration → Device Registration'''
[[File:Fig1 device registration1.png|Fig. 1. Device Registration Menu]]
*A device '''registration form''' will appear on the screen.
[[File:Fig2 device registration window.png|Fig. 2. Device Registration Form]]
*Unpack your '''Baozam device''' and find the '''Baozam card''' (the figure shows an example of a '''people counter''' with a '''card''') (fig.3)
[[File:Fig3 device registration ppl ctr w card.png|Fig. 3. Baozam device with card]]
*Erase the '''scratch strip''' from the card.
[[File:Fig4 device registration card stripe rmvd.png|Fig. 4. Baozam card without scratch strip]]
*Fill form fields with '''serial number''' of the '''Baozam card''' and '''PIN-code'''.
[[File:Fig7 device registration form fill.png|Fig. 6. Fill the form]]
*'''Other way. '''To go to the registration form '''quickly''' and enter the card number you can use the link in the '''QR-code''' printed on the card. Use the code scanning program and follow the link. '''Attention!''' You must first log into your '''Baozam account''' on the device with which you scan the '''QR-code''' and follow the link.
[[File:Fig5 device registration card QR scanner.png|Fig. 7. Scan QR-code]] 
[[File:Fig6 device registration card QR link.png|Fig. 8. Follow the link]]
*You will be informed about the name, serial number and basic parameters of the attached device. (fig8)
[[File:Fig8 device success added.png|Fig. 8. Device information]]
*Now you can check the status of your '''inventory'''.
[[File:Fig9 inventory check1.png|Fig. 9. Inventory Menu]] 
[[File:Fig10 inventory check2.png|Fig. 10. Inventory]]

Register your devices

2018-12-06T12:57:28Z

Monster: /* Device registration */

==Device registration==
Once you have already successfully created your '''Baozam account''', it's time to add your first '''Baozam device'''.
The '''registration procedure''' for all '''Baozam devices''' is the same. At the production stage each '''Baozam device''' is registered in the device database. Each device is already fully functional and can work with cloud services. But it still does not have an '''owner''' and '''nobody can access''' to its data and control functions.
A link between the '''Baozam device''' and its '''owner''' is provided with a '''Baozam card''' that is attached to each device. This card has a number and PIN-code by entering which the user declares himself as the '''owner''' of the device and binds the device with his account. '''Attention! The card can be used only once.''' 
===Registration procedure:===
*Log in into your '''Baozam account''' on baozam.net
*In main menu choose '''Configuration → Device Registration'''
[[File:Fig1 device registration1.png|Fig. 1. Device Registration Menu]]
*A device '''registration form''' will appear on the screen.
[[File:Fig2 device registration window.png|Fig. 2. Device Registration Form]]
*Unpack your '''Baozam device''' and find the '''Baozam card''' (the figure shows an example of a '''people counter''' with a '''card''') (fig.3)
[[File:Fig3 device registration ppl ctr w card.png|Fig. 3. Baozam device with card]]
*Erase the '''scratch strip''' from the card.
[[File:Fig4 device registration card stripe rmvd.png|Fig. 4. Baozam card without scratch strip]]
*Fill form fields with '''serial number''' of the '''Baozam card''' and '''PIN-code'''.
[[File:Fig7 device registration form fill.png|Fig. 6. Fill the form]]
*'''Other way. '''To go to the registration form '''quickly''' and enter the card number you can use the link in the '''QR-code''' printed on the card. Use the code scanning program and follow the link. '''Attention!''' You must first log into your '''Baozam account''' on the device with which you scan the '''QR-code''' and follow the link.
[[File:Fig5 device registration card QR scanner.png|Fig. 7. Scan QR-code]]
[[File:Fig6 device registration card QR link.png|Fig. 8. Follow the link]]
*You will be informed about the name, serial number and basic parameters of the attached device. (fig8)
[[File:Fig8 device success added.png|Fig. 8. Device information]]
*Now you can check the status of your '''inventory'''.
[[File:Fig9 inventory check1.png|Fig. 9. Inventory Menu]]
[[File:Fig10 inventory check2.png|Fig. 10. Inventory]]

Register your devices

2018-12-06T12:56:47Z

Monster: /* Device registration */

==Device registration==
Once you have already successfully created your '''Baozam account''', it's time to add your first '''Baozam device'''.
The '''registration procedure''' for all '''Baozam devices''' is the same. At the production stage each '''Baozam device''' is registered in the device database. Each device is already fully functional and can work with cloud services. But it still does not have an '''owner''' and '''nobody can access''' to its data and control functions.
A link between the '''Baozam device''' and its '''owner''' is provided with a '''Baozam card''' that is attached to each device. This card has a number and PIN-code by entering which the user declares himself as the '''owner''' of the device and binds the device with his account. '''Attention! The card can be used only once.''' 
Registration procedure: 
*Log in into your '''Baozam account''' on baozam.net
*In main menu choose '''Configuration → Device Registration'''
[[File:Fig1 device registration1.png|Fig. 1. Device Registration Menu]]
*A device '''registration form''' will appear on the screen.
[[File:Fig2 device registration window.png|Fig. 2. Device Registration Form]]
*Unpack your '''Baozam device''' and find the '''Baozam card''' (the figure shows an example of a '''people counter''' with a '''card''') (fig.3)
[[File:Fig3 device registration ppl ctr w card.png|Fig. 3. Baozam device with card]]
*Erase the '''scratch strip''' from the card.
[[File:Fig4 device registration card stripe rmvd.png|Fig. 4. Baozam card without scratch strip]]
*Fill form fields with '''serial number''' of the '''Baozam card''' and '''PIN-code'''.
[[File:Fig7 device registration form fill.png|Fig. 6. Fill the form]]
*'''Other way. '''To go to the registration form '''quickly''' and enter the card number you can use the link in the '''QR-code''' printed on the card. Use the code scanning program and follow the link. '''Attention!''' You must first log into your '''Baozam account''' on the device with which you scan the '''QR-code''' and follow the link.
[[File:Fig5 device registration card QR scanner.png|Fig. 7. Scan QR-code]]
[[File:Fig6 device registration card QR link.png|Fig. 8. Follow the link]]
*You will be informed about the name, serial number and basic parameters of the attached device. (fig8)
[[File:Fig8 device success added.png|Fig. 8. Device information]]
*Now you can check the status of your '''inventory'''.
[[File:Fig9 inventory check1.png|Fig. 9. Inventory Menu]]
[[File:Fig10 inventory check2.png|Fig. 10. Inventory]]

Baozam Howto

2018-12-06T12:56:12Z

Monster:

== Baozam Howto ==
* [[Create an account]]
* [[Register your devices]]
* [[Tune your devices]]
* [[Use streams and events]]

Main Page

2018-12-06T12:55:06Z

Monster: /* Common procedures */

== Devices ==
* [[Acousto-magnetic EAS systems]]
* [[Iridium mono 2k IR 1040 06 V4|Iridium mono RF systems]]
* [[Bidirectional pass counters]]
* [[Combies|Combies or Combined Magnet Metal detection systems ]]
* [[Magnet detector]]

== Common procedures ==
* [[Baozam Usage]]
* [[WiFi Setup Common|WiFi setup procedures]]
* [[Device tuning via the baozam.net website]]
* [[Data export]]
* [[Local tuner software]]
* [[Baozam Howto | Baozam How To]]

== Miscellaneous ==
* [[CMD:000|Manual List of known commands]]
* [{{fullurl:Special:Allpages|namespace=3000}} List of described commands]
* [[Parameter types]]

[[uk:Головна сторінка]]
[[ru:Заглавная_страница]]

Create an account

2018-12-06T12:48:17Z

Monster: /* Create an account */

==Create an account==
* Follow the link: [https://baozam.net www.baozam.net].
[[File:Fig1 login page.png|Fig. 1. Baozam login page]]
* If you have not been logged before, an invitation to log in will appear on the screen. If you want to create a new account press „Create New Account” button. The following form appears.
[[File:Fig2 create new account.png|Fig. 2. Baozam new account form]]
* Fill the fields of this form with your User name (any name which you'll use in the future to log in into Baozam), your valid e-mail address (will be used for account activation and service messaging. Also you can use it instead of User name while logging in), password (must contain at least 7 symbols including at least one letter and one numeral) and optional Company Name (will be used as a group identifier for your devices). Press „Create New Account”
* Example:
[[File:Fig3 create new account filled.png|Fig. 3. Baozam new account form example]]
*If you'll try to pick already existing User name, use already existing e-mail address or type illegal (in terms of strength) password, you'll be warned by Baozam. In this case fill the form anew and submit it again.
*After successfull filling the form the following prompt appears.
[[File:Fig4 create new account confirmation.png|Fig. 4. Confirmation]]
*Check the email you provided when filling out the registration form. You should receive an email with a link to activate your account. In some cases, the letter may arrive within 10-15 minutes or be placed in the spam folder.
[[File:Fig5 email confirmation1.png|Fig. 5. Check email for confirmation letter]]
[[File:Fig6 email confirmation2.png|Fig. 6. Follow the confirmation link]]
*Follow the link you received.
[[File:Fig7 create new account confirmation1.png|Fig. 7. Congratulations]]
*Congratulations! You just signed up for Baozam.net.
*Initially you have no linked devices and your dashboard looks like
[[File:Fig8 dashboard empty.png|Fig. 8. Dashboard view]]
*To complete settings please specify your tome zone. All baozam devices use UTC+0 timezone. If you'll use some baozam devices in future their data timestamps will be recalculated using your time zone. Press Account settings button (top-right part of screen) then choose your time zone from drop-down list and press „Update” button.
[[File:Fig9 personal info.png|Fig. 9. Edit your personal data]] 
[[File:Fig10 edit timezone.png|Fig. 10. Edit and update your personal information]]

Create an account

2018-12-06T12:45:35Z

Monster: /* Create an account */

==Create an account==
* Follow the link: www.baozam.net
[[File:Fig1 login page.png|Fig. 1. Baozam login page]]
* If you have not been logged before, an invitation to log in will appear on the screen. If you want to create a new account press „Create New Account” button. The following form appears.
[[File:Fig2 create new account.png|Fig. 2. Baozam new account form]]
* Fill the fields of this form with your User name (any name which you'll use in the future to log in into Baozam), your valid e-mail address (will be used for account activation and service messaging. Also you can use it instead of User name while logging in), password (must contain at least 7 symbols including at least one letter and one numeral) and optional Company Name (will be used as a group identifier for your devices). Press „Create New Account”
* Example:
[[File:Fig3 create new account filled.png|Fig. 3. Baozam new account form example]]
*If you'll try to pick already existing User name, use already existing e-mail address or type illegal (in terms of strength) password, you'll be warned by Baozam. In this case fill the form anew and submit it again.
*After successfull filling the form the following prompt appears.
[[File:Fig4 create new account confirmation.png|Fig. 4. Confirmation]]
*Check the email you provided when filling out the registration form. You should receive an email with a link to activate your account. In some cases, the letter may arrive within 10-15 minutes or be placed in the spam folder.
[[File:Fig5 email confirmation1.png|Fig. 5. Check email for confirmation letter]]
[[File:Fig6 email confirmation2.png|Fig. 6. Follow the confirmation link]]
*Follow the link you received.
[[File:Fig7 create new account confirmation1.png|Fig. 7. Congratulations]]
*Congratulations! You just signed up for Baozam.net.
*Initially you have no linked devices and your dashboard looks like
[[File:Fig8 dashboard empty.png|Fig. 8. Dashboard view]]
*To complete settings please specify your tome zone. All baozam devices use UTC+0 timezone. If you'll use some baozam devices in future their data timestamps will be recalculated using your time zone. Press Account settings button (top-right part of screen) then choose your time zone from drop-down list and press „Update” button.
[[File:Fig9 personal info.png|Fig. 9. Edit your personal data]] 
[[File:Fig10 edit timezone.png|Fig. 10. Edit and update your personal information]]

Create an account

2018-12-06T12:40:10Z

Monster: /* Create an account */

==Create an account==
* Follow the link: www.baozam.net
[[File:Fig1 login page.png|Fig. 1. Baozam login page]]
* If you have not been logged before, an invitation to log in will appear on the screen. If you want to create a new account press „Create New Account” button. The following form appears.
[[File:Fig2 create new account.png|Fig. 2. Baozam new account form]]
* Fill the fields of this form with your User name (any name which you'll use in the future to log in into Baozam), your valid e-mail address (will be used for account activation and service messaging. Also you can use it instead of User name while logging in), password (must contain at least 7 symbols including at least one letter and one numeral) and optional Company Name (will be used as a group identifier for your devices). Press „Create New Account”
* Example:
[[File:Fig3 create new account filled.png|Fig. 3. Baozam new account form example]]
*If you'll try to pick already existing User name, use already existing e-mail address or type illegal (in terms of strength) password, you'll be warned by Baozam. In this case fill the form anew and submit it again.
*After successfull filling the form the following prompt appears.
[[File:Fig4 create new account confirmation.png|Fig. 4. Confirmation]]
*Check the email you provided when filling out the registration form. You should receive an email with a link to activate your account. In some cases, the letter may arrive within 10-15 minutes or be placed in the spam folder.
[[File:Fig5 email confirmation1.png|Fig. 5. Check email for confirmation letter]]
[[File:Fig6 email confirmation2.png|Fig. 6. Follow the confirmation link]]
*Follow the link you received.
[[File:Fig7 create new account confirmation1.png|Fig. 7. Congratulations]]
*Congratulations! You just signed up for Baozam.net.
*Initially you have no linked devices and your dashboard looks like
[[File:Fig8 dashboard empty.png|Fig. 8. Dashboard view]]
*To complete settings please specify your tome zone. All baozam devices use UTC+0 timezone. If you'll use some baozam devices in future their data timestamps will be recalculated using your time zone. Press Account settings button (top-right part of screen) then choose your time zone from drop-down list and press „Update” button.
[[File:Fig9 personal info.png|Fig. 9. Edit your personal data]]
[[File:Fig10 edit timezone.png|Fig. 10. Edit and update your personal information]]

Register your devices

2018-12-06T12:38:06Z

Monster: /* Device registration */

==Device registration==
Once you have already successfully created your '''Baozam account''', it's time to add your first '''Baozam device'''.
The '''registration procedure''' for all '''Baozam devices''' is the same. At the production stage each '''Baozam device''' is registered in the device database. Each device is already fully functional and can work with cloud services. But it still does not have an '''owner''' and '''nobody can access''' to its data and control functions.
A link between the '''Baozam device''' and its '''owner''' is provided with a '''Baozam card''' that is attached to each device. This card has a number and PIN-code by entering which the user declares himself as the '''owner''' of the device and binds the device with his account. '''The card can be used only once.''' 
Registration procedure: 
*Log in into your '''Baozam account''' on baozam.net
*In main menu choose '''Configuration → Device Registration'''
[[File:Fig1 device registration1.png|Fig. 1. Device Registration Menu]]
*A device '''registration form''' will appear on the screen.
[[File:Fig2 device registration window.png|Fig. 2. Device Registration Form]]
*Unpack your '''Baozam device''' and find the '''Baozam card''' (the figure shows an example of a '''people counter''' with a '''card''') (fig.3)
[[File:Fig3 device registration ppl ctr w card.png|Fig. 3. Baozam device with card]]
*Erase the '''scratch strip''' from the card.
[[File:Fig4 device registration card stripe rmvd.png|Fig. 4. Baozam card without scratch strip]]
*Fill form fields with '''serial number''' of the '''Baozam card''' and '''PIN-code'''.
[[File:Fig7 device registration form fill.png|Fig. 6. Fill the form]]
*'''Other way. '''To go to the registration form '''quickly''' and enter the card number you can use the link in the '''QR-code''' printed on the card. Use the code scanning program and follow the link. '''Attention!''' You must first log into your '''Baozam account''' on the device with which you scan the '''QR-code''' and follow the link.
[[File:Fig5 device registration card QR scanner.png|Fig. 7. Scan QR-code]]
[[File:Fig6 device registration card QR link.png|Fig. 8. Follow the link]]
*You will be informed about the name, serial number and basic parameters of the attached device. (fig8)
[[File:Fig8 device success added.png|Fig. 8. Device information]]
*Now you can check the status of your '''inventory'''.
[[File:Fig9 inventory check1.png|Fig. 9. Inventory Menu]]
[[File:Fig10 inventory check2.png|Fig. 10. Inventory]]

Register your devices

2018-12-06T12:33:29Z

Monster: /* Device registration */

==Device registration==
Once you have already successfully created your '''Baozam account''', it's time to add your first '''Baozam device'''.
The '''registration procedure''' for all '''Baozam devices''' is the same. At the production stage each '''Baozam device''' is registered in the device database. Each device is already fully functional and can work with cloud services. But it still does not have an '''owner''' and '''nobody can access''' to its data and control functions.
A link between the '''Baozam device''' and its '''owner''' is provided with a '''Baozam card''' that is attached to each device. This card has a number and PIN-code by entering which the user declares himself as the '''owner''' of the device and binds the device with his account. '''The card can be used only once.''' 
Registration procedure: 
*Log in into your account on baozam.net
*In main menu choose '''Configuration → Device Registration'''
[[File:Fig1 device registration1.png|center|Fig. 1. Device Registration Menu]]
*A device '''registration form''' will appear on the screen.
[[File:Fig2 device registration window.png|center|Fig. 2. Device Registration Form]]
*Unpack your '''Baozam device''' and find the '''Baozam card''' (the figure shows an example of a '''people counter''' with a '''card''') (fig.3)
[[File:Fig3 device registration ppl ctr w card.png|center|Fig. 3. Baozam device with card]]
*Erase the '''scratch strip''' from the card.
[[File:Fig4 device registration card stripe rmvd.png|center|Fig. 4. Baozam card without scratch strip]]
*Fill form fields with '''serial number''' of the '''Baozam card''' and '''PIN-code'''.
[[File:Fig7 device registration form fill.png|center|Fig. 6. Fill the form]]
*'''Other way. '''To go to the registration form '''quickly''' and enter the card number you can use the link in the '''QR-code''' printed on the card. Use the code scanning program and follow the link. '''Attention!''' You must first log into your '''Baozam account''' on the device with which you scan the '''QR-code''' and follow the link.
[[File:Fig5 device registration card QR scanner.png|center|Fig. 7. Scan QR-code]]
[[File:Fig6 device registration card QR link.png|center|Fig. 8. Follow the link]]
*You will be informed about the name, serial number and basic parameters of the attached device. (fig8)
[[File:Fig8 device success added.png|center|Fig. 8. Device information]]
*Now you can check the status of your '''inventory'''.
[[File:Fig9 inventory check1.png|center|Fig. 9. Inventory Menu]]
[[File:Fig10 inventory check2.png|center|Fig. 10. Inventory]]

Register your devices

2018-12-06T12:26:46Z

Monster: Created page with "==Device registration== Once you have already successfully created your '''Baozam account''', it's time to add your first '''Baozam device'''. The '''registration procedure''..."

==Device registration==
Once you have already successfully created your '''Baozam account''', it's time to add your first '''Baozam device'''.
The '''registration procedure''' for all '''Baozam devices''' is the same. At the production stage each '''Baozam device''' is registered in the device database. Each device is already fully functional and can work with cloud services. But it still does not have an '''owner''' and '''nobody can access''' to its data and control functions.
A link between the '''Baozam device''' and its '''owner''' is provided with a '''Baozam card''' that is attached to each device. This card has a number and PIN-code by entering which the user declares himself as the '''owner''' of the device and binds the device with his account. '''The card can be used only once.''' 
Registration procedure: 
*Log in into your account on baozam.net
*In main menu choose '''Configuration → Device Registration'''
[[File:Fig1 device registration1.png|center|Fig. 1. Device Registration Menu]]
*A device '''registration form''' will appear on the screen.
[[File:Fig2 device registration window.png|center|Fig. 2. Device Registration Form]]
*Unpack your '''Baozam device''' and find the '''Baozam card''' (the figure shows an example of a '''people counter''' with a '''card''') (fig.3)
[[File:Fig3 device registration ppl ctr w card.png|center|Fig. 3. Baozam device with card]]
*Erase the '''scratch strip''' from the card.
[[File:Fig4 device registration card stripe rmvd.png|center|Fig. 4. Baozam card without scratch strip]]
*To go to the registration of '''Baozam devices''' and enter the card number '''quickly''' you can use the link in the '''QR-code''' printed on the card. Use the code scanning program and follow the link. '''Attention!''' You must first log into your '''Baozam account''' on the device with which you scan the '''QR-code''' and follow the link. (Fig5,6)
[[File:Fig5 device registration card QR scanner.png|center|Fig. 5. Scan QR-code]]
[[File:Fig6 device registration card QR link.png|center|Fig. 6. Follow the link]]
*Fill form fields with '''serial number''' of the '''Baozam card''' and '''PIN-code'''.
[[File:Fig7 device registration form fill.png|center|Fig. 7. Fill the form]]
*You will be informed about the name, serial number and basic parameters of the attached device. (fig8)
[[File:Fig8 device success added.png|center|Fig. 8. Device information]]
*Now you can check the status of your '''inventory'''. (fig9,10)
[[File:Fig9 inventory check1.png|center|Fig. 9. Inventory Menu]]
[[File:Fig10 inventory check2.png|center|Fig. 10. Inventory]]

File:Fig10 inventory check2.png

2018-12-06T12:25:44Z

Monster:

File:Fig9 inventory check1.png

2018-12-06T12:25:02Z

Monster:

File:Fig8 device success added.png

2018-12-06T12:24:15Z

Monster:

File:Fig7 device registration form fill.png

2018-12-06T12:23:17Z

Monster:

File:Fig6 device registration card QR link.png

2018-12-06T12:22:32Z

Monster:

File:Fig5 device registration card QR scanner.png

2018-12-06T12:21:39Z

Monster:

File:Fig4 device registration card stripe rmvd.png

2018-12-06T12:19:22Z

Monster:

File:Fig3 device registration ppl ctr w card.png

2018-12-06T12:18:35Z

Monster:

File:Fig2 device registration window.png

2018-12-06T12:16:09Z

Monster:

File:Fig1 device registration1.png

2018-12-06T12:14:50Z

Monster:

Create an account

2018-12-05T13:18:47Z

Monster: Created page with "==Create an account== * Follow the link: www.baozam.net Fig. 1. Baozam login page * If you have not been logged before, an invitation to lo..."

==Create an account==
* Follow the link: www.baozam.net
[[File:Fig1 login page.png|center|Fig. 1. Baozam login page]]
* If you have not been logged before, an invitation to log in will appear on the screen. If you want to create a new account press „Create New Account” button. The following form appears.
[[File:Fig2 create new account.png|center|Fig. 2. Baozam new account form]]
* Fill the fields of this form with your User name (any name which you'll use in the future to log in into Baozam), your valid e-mail address (will be used for account activation and service messaging. Also you can use it instead of User name while logging in), password (must contain at least 7 symbols including at least one letter and one numeral) and optional Company Name (will be used as a group identifier for your devices). Press „Create New Account”
* Example:
[[File:Fig3 create new account filled.png|center|Fig. 3. Baozam new account form example]]
*If you'll try to pick already existing User name, use already existing e-mail address or type illegal (in terms of strength) password, you'll be warned by Baozam. In this case fill the form anew and submit it again.
*After successfull filling the form the following prompt appears.
[[File:Fig4 create new account confirmation.png|center|Fig. 4. Confirmation]]
*Check the email you provided when filling out the registration form. You should receive an email with a link to activate your account. In some cases, the letter may arrive within 10-15 minutes or be placed in the spam folder.
[[File:Fig5 email confirmation1.png|center|Fig. 5. Check email for confirmation letter]]
[[File:Fig6 email confirmation2.png|center|Fig. 6. Follow the confirmation link]]
*Follow the link you received.
[[File:Fig7 create new account confirmation1.png|center|Fig. 7. Congratulations]]
*Congratulations! You just signed up for Baozam.net.
*Initially you have no linked devices and your dashboard looks like
[[File:Fig8 dashboard empty.png|center|Fig. 8. Dashboard view]]
*To complete settings please specify your tome zone. All baozam devices use UTC+0 timezone. If you'll use some baozam devices in future their data timestamps will be recalculated using your time zone. Press Account settings button (top-right part of screen) then choose your time zone from drop-down list and press „Update” button.
[[File:Fig9 personal info.png|center|Fig. 9. Edit your personal data]]
[[File:Fig10 edit timezone.png|center|Fig. 10. Edit and update your personal information]]

File:Fig10 edit timezone.png

2018-12-05T13:16:39Z

Monster:

File:Fig8 dashboard empty.png

2018-12-05T13:15:49Z

Monster:

File:Fig9 personal info.png

2018-12-05T13:13:53Z

Monster:

File:Fig7 create new account confirmation1.png

2018-12-05T13:12:35Z

Monster:

File:Fig6 email confirmation2.png

2018-12-05T13:11:03Z

Monster:

File:Fig5 email confirmation1.png

2018-12-05T13:09:55Z

Monster:

File:Fig4 create new account confirmation.png

2018-12-05T13:08:06Z

Monster:

File:Fig3 create new account filled.png

2018-12-05T13:06:10Z

Monster:

File:Fig2 create new account.png

2018-12-05T13:04:08Z

Monster:

File:Fig1 login page.png

2018-12-05T13:00:41Z

Monster:

Baozam Howto

2018-12-05T12:57:25Z

Monster: Created page with "== Baozam Howto == * Create an account * Register your devices * Tune your devices"

== Baozam Howto ==
* [[Create an account]]
* [[Register your devices]]
* [[Tune your devices]]

Main Page

2018-12-05T12:55:36Z

Monster: /* Common procedures */

== Devices ==
* [[Acousto-magnetic EAS systems]]
* [[Iridium mono 2k IR 1040 06 V4|Iridium mono RF systems]]
* [[Bidirectional pass counters]]
* [[Combies|Combies or Combined Magnet Metal detection systems ]]
* [[Magnet detector]]

== Common procedures ==
* [[Baozam Usage]]
* [[WiFi Setup Common|WiFi setup procedures]]
* [[Device tuning via the baozam.net website]]
* [[Data export]]
* [[Local tuner software]]
* [[Baozam Howto]]

== Miscellaneous ==
* [[CMD:000|Manual List of known commands]]
* [{{fullurl:Special:Allpages|namespace=3000}} List of described commands]
* [[Parameter types]]

[[uk:Головна сторінка]]
[[ru:Заглавная_страница]]

MagnetGuard V2 - Sensor Adjustment

2018-11-25T14:05:03Z

Monster: /* Sensor Adjustment */

== Sensor Adjustment ==
[[File:Magnetguard v2 sensor 1.png|600px|center|Sensor]]
=== Sensitivity adjustment ===
Sensor sensitivity provides the ability to choose the level of sensor response to magnetic field changes. It let us obtain the required detection range free of false alarms. 
Sensor sensitivity adjustment process is performed by consecutive pressing the button 2 «Sens» to choose the required sensitivity level. LED1 will be activated and LED 2 will make number of blinks which corresponds with the selected sensitivity level (refer to the table, default setting is highlighted). 
Sensitivity settings of the sensor:
{|border=1 cellpadding=5
|-
| LED2 flashes || Approx. magnetic field changes threshold, nТl || Sensitivity level
|-
| 1 || 380 || Very high
|-
| 2 || 450 || High
|-
| 3 || 500 || High (default)
|-
| 4 || 630 || High to intermediate
|-
| 5 || 900 || Intermediate
|-
| 6 || 1000 || Intermediate
|-
| 7 || 1200 || Intermediate
|-
| 8 || 1400 || Intermediate to low
|-
| 9 || 1600 || Low
|-
| 10 || 1800 || Low
|}

=== Criteria adjustment ===
Criteria adjustment let us maintain the time needed for magnetic field changes to be recognised as a detacher. This allows to eliminate false alarms caused by phones, bags with magnet locks or magnetic random noise (high current commutation) which occur mostly for a very short period of time. 
Criteria adjustment process is performed by consecutive pressing on the button 1 «Criteria» to choose the criteria settings number. LED2 will be activated and LED 1 will make number of blinks which corresponds with the selected criteria level (refer to the table, default setting is highlighted). 
Criteria settings of the sensor:
{|border=1 cellpadding=5
|-
| LED1 flashes || Approx. min. detection time / max. filter time, sec|| Criteria level
|-
| 1 || 0,02/0,2 || No filtering
|-
| 2 || 0,2/0,6 || Very high
|-
| 3 || 0,4/1,2 || High (default)
|-
| 4 || 0,6/1,5 || High to intermediate
|-
| 5 || 0,9/1,9 || Intermediate
|-
| 6 || 1,1/2,3 || Intermediate
|-
| 7 || 1,3/2,7 || Intermediate
|-
| 8 || 1,5/3,1 || Intermediate to low
|-
| 9 || 1,7/3,5 || Low
|-
| 10 || 1,9/3,9 || Low
|}

MagnetGuard V2 - General installation issues

2018-11-25T13:58:50Z

Monster: /* Common noise sources */

== General installation issues ==
===Common noise sources===
:- moving objects containing metal (sliding doors, elevators, cash machines, payment terminals, trolleys etc.) 
:- smartphones and tablets nearby (especially with magnetic covers) 
:- magnetic locks and clips (often used in bags) 
:- railway, trams or busy roads with heavy traffic situated very close to the shop 

===Installation guidelines for optimum performance===
:- Check the installation area for possible noise sources prior to installation.
:- Avoid any metal objects mentioned above.
:- Locate the central unit in a visible place for the shop/security staff. The distance between central unit and sensors should be less then 50 meters (depends on radio interference).
:- Choose a location for the microprocessor magnetic field sensors on a non-metallic surfaces and fix them at a height of about 1 - 1,3 meter using double-sided tape.
:- We recommend to use only one sensor pro fitting room if it is not wider than one meter.
:- Although the default settings of the sensors should work fine in most situations, it can be necessary to fine-tune the sensors for best performance in your specific environment (sensitivity and criteria adjustment).
:- Try to keep the sensor sensitivity as low as possible in order to avoid false alarms.
:- It is not necessary to get an alarm immediately during entering the fitting room as the detacher can be hidden and carried into the fitting room far away from the sensor. Alarm will be activated as soon as the thief will start to operate with the detacher to remove the hard tags - make adequate tests.
:- Don't transport the sensors with battery inside. The sensors will try to send information to the unplugged central unit permanently and will drain the battery. It is better to insert the battery directly before the installation.

[[File:Magnetguard v2 fitting room 1.png|600px|center|Fitting room installation example]]

MagnetGuard V2 - General installation issues

2018-11-25T13:58:02Z

Monster: /* Noise sources */

== General installation issues ==
===Common noise sources===
The list below shows usual sources of magnetic noise: 
:- moving objects containing metal (sliding doors, elevators, cash machines, payment terminals, trolleys etc.) 
:- smartphones and tablets nearby (especially with magnetic covers) 
:- magnetic locks and clips (often used in bags) 
:- railway, trams or busy roads with heavy traffic situated very close to the shop 

===Installation guidelines for optimum performance===
:- Check the installation area for possible noise sources prior to installation.
:- Avoid any metal objects mentioned above.
:- Locate the central unit in a visible place for the shop/security staff. The distance between central unit and sensors should be less then 50 meters (depends on radio interference).
:- Choose a location for the microprocessor magnetic field sensors on a non-metallic surfaces and fix them at a height of about 1 - 1,3 meter using double-sided tape.
:- We recommend to use only one sensor pro fitting room if it is not wider than one meter.
:- Although the default settings of the sensors should work fine in most situations, it can be necessary to fine-tune the sensors for best performance in your specific environment (sensitivity and criteria adjustment).
:- Try to keep the sensor sensitivity as low as possible in order to avoid false alarms.
:- It is not necessary to get an alarm immediately during entering the fitting room as the detacher can be hidden and carried into the fitting room far away from the sensor. Alarm will be activated as soon as the thief will start to operate with the detacher to remove the hard tags - make adequate tests.
:- Don't transport the sensors with battery inside. The sensors will try to send information to the unplugged central unit permanently and will drain the battery. It is better to insert the battery directly before the installation.

[[File:Magnetguard v2 fitting room 1.png|600px|center|Fitting room installation example]]

MagnetGuard V2 - General installation issues

2018-11-25T13:55:37Z

Monster: /* Noise sources */

== General installation issues ==
===Noise sources===
The list below shows possible noise sources: 
:- moving objects containing metal (sliding doors, elevators, cash machines, payment terminals, trolleys etc.) 
:- smartphones and tablets nearby (especially with magnetic covers) 
:- magnetic locks and clips (often used in bags) 
:- railway, trams or busy roads with heavy traffic situated very close to the shop 

===Installation guidelines for optimum performance===
:- Check the installation area for possible noise sources prior to installation.
:- Avoid any metal objects mentioned above.
:- Locate the central unit in a visible place for the shop/security staff. The distance between central unit and sensors should be less then 50 meters (depends on radio interference).
:- Choose a location for the microprocessor magnetic field sensors on a non-metallic surfaces and fix them at a height of about 1 - 1,3 meter using double-sided tape.
:- We recommend to use only one sensor pro fitting room if it is not wider than one meter.
:- Although the default settings of the sensors should work fine in most situations, it can be necessary to fine-tune the sensors for best performance in your specific environment (sensitivity and criteria adjustment).
:- Try to keep the sensor sensitivity as low as possible in order to avoid false alarms.
:- It is not necessary to get an alarm immediately during entering the fitting room as the detacher can be hidden and carried into the fitting room far away from the sensor. Alarm will be activated as soon as the thief will start to operate with the detacher to remove the hard tags - make adequate tests.
:- Don't transport the sensors with battery inside. The sensors will try to send information to the unplugged central unit permanently and will drain the battery. It is better to insert the battery directly before the installation.

[[File:Magnetguard v2 fitting room 1.png|600px|center|Fitting room installation example]]

MagnetGuard V2 - General installation issues

2018-11-25T13:53:57Z

Monster: /* Noise sources */

== General installation issues ==
===Noise sources===
The list below shows possible noise sources: 
:- moving objects containing metal (sliding doors, elevators, cash machines, payment terminals, trolleys etc.) 
:- smartphones and tablets nearby (especially with magnetic covers) 
:-
:- railway, trams or busy roads with heavy traffic situated very close to the shop 

===Installation guidelines for optimum performance===
:- Check the installation area for possible noise sources prior to installation.
:- Avoid any metal objects mentioned above.
:- Locate the central unit in a visible place for the shop/security staff. The distance between central unit and sensors should be less then 50 meters (depends on radio interference).
:- Choose a location for the microprocessor magnetic field sensors on a non-metallic surfaces and fix them at a height of about 1 - 1,3 meter using double-sided tape.
:- We recommend to use only one sensor pro fitting room if it is not wider than one meter.
:- Although the default settings of the sensors should work fine in most situations, it can be necessary to fine-tune the sensors for best performance in your specific environment (sensitivity and criteria adjustment).
:- Try to keep the sensor sensitivity as low as possible in order to avoid false alarms.
:- It is not necessary to get an alarm immediately during entering the fitting room as the detacher can be hidden and carried into the fitting room far away from the sensor. Alarm will be activated as soon as the thief will start to operate with the detacher to remove the hard tags - make adequate tests.
:- Don't transport the sensors with battery inside. The sensors will try to send information to the unplugged central unit permanently and will drain the battery. It is better to insert the battery directly before the installation.

[[File:Magnetguard v2 fitting room 1.png|600px|center|Fitting room installation example]]

Magnet detector

2018-11-25T13:51:31Z

Monster: /* Alarming device (Control panel) */

[[File:Magnetguard v2 photo 1.png|300px|thumb|Magnetguard wireless]]
''MagnetGuard Wireless'' is designed for installation in shop entrances, passages and in fitting rooms to detect and alert personnel about the presence of powerful permanent magnets. Powerful magnets can be used for unauthorized removal of security sensors from the goods. The system consists of wireless magnetic sensors and wireless alarming devices for the personnel. The sensors are battery-powered and designed for optimal power consumption modes resulting in one to three years of battery life, depending on selected operating mode. Easy and transparent system installation and configuration for end users with "one-touch" deployment.

== Specifications ==
===Magnet sensor specifications===
{|border=1 cellpadding=5
|-
|Power supply ||Lithium cell AA ER14505 (3.6V 2.4Ah)
|-
|Dimensions (W x H x D) ||80mm x 40mm x 20mm
|-
|Color ||Gray, Black
|-
|Mounting ||Using double-sided adhesive tape; The flanges
|-
|Detacher detection distance* ||Up to 1.5m in all directions
|-
|Controls ||2 buttons inside («connect/reset» and «mode»)
|-
|RF band ||2.4 GHz
|-
|Radio transmission distance** ||Up to 50m (in open field)
|-
|Communication protocol ||IEEE 802.15.4 compatible
|-
|Number of supported alarming devices ||Up to 10 alarming devices
|}
:<nowiki>*</nowiki>The detection distance depends on the magnetic properties and construction of magnetic detacher and sensitivity settings.
:<nowiki>**</nowiki>The transmission distance depends on many factors ( the presence of the shielding structures, the mutual orientation of the devices, etc. )

===Alarming device (Control panel) specifications===
{|border=1 cellpadding=5
|-
|Power supply ||5-12V, 0.5A (from external power adapter)
|-
|Dimensions (W x H x D)||80mm x 40mm x 20mm
|-
|Color ||Black
|-
|Mounting ||Using double-sided adhesive tape
|-
|Indication ||Audible (alarm), LED (alarm zone number)
|-
|Controls ||2 buttons on the front panel ("connect/reset" and "alarm mode")
|-
|RF band ||2.4 GHz
|-
|Communication protocol ||IEEE 802.15.4 compatible
|-
|Number of supported sensors ||Up to 10 sensors
|}
Limitations on usage:
:- Installation of sensors is not closer than 1m from moving metal objects;
:- Installation of sensors is not closer than 0.5m from the power wiring and acousto-magnetic anti theft systems;
:- Installation of the system is not closer than 50m from the metro lines and electric trains, not closer than 20m from the transformer substations and high tension power distribution lines.

== Installation ==
* [[MagnetGuard V2 - General installation issues | General installation issues]] 
* [[MagnetGuard V2 - The Central Unit | The Central Unit]] 
* [[MagnetGuard V2 - The Sensor | The Sensor]] 
* [[MagnetGuard V2 - Initial configuration of the system | Initial configuration of the system]] 
* [[MagnetGuard V2 - Sensor Adjustment | Sensor Adjustment]] 
* [[MagnetGuard V2 - Installation procedure | Installation procedure]] 

== How To ==
* [[How to setup Magnet detector Control panels in repeating mode]]

[[Category:Magnet detector|*]]

Magnet detector

2018-11-25T13:51:14Z

Monster: /* Magnet sensor */

[[File:Magnetguard v2 photo 1.png|300px|thumb|Magnetguard wireless]]
''MagnetGuard Wireless'' is designed for installation in shop entrances, passages and in fitting rooms to detect and alert personnel about the presence of powerful permanent magnets. Powerful magnets can be used for unauthorized removal of security sensors from the goods. The system consists of wireless magnetic sensors and wireless alarming devices for the personnel. The sensors are battery-powered and designed for optimal power consumption modes resulting in one to three years of battery life, depending on selected operating mode. Easy and transparent system installation and configuration for end users with "one-touch" deployment.

== Specifications ==
===Magnet sensor specifications===
{|border=1 cellpadding=5
|-
|Power supply ||Lithium cell AA ER14505 (3.6V 2.4Ah)
|-
|Dimensions (W x H x D) ||80mm x 40mm x 20mm
|-
|Color ||Gray, Black
|-
|Mounting ||Using double-sided adhesive tape; The flanges
|-
|Detacher detection distance* ||Up to 1.5m in all directions
|-
|Controls ||2 buttons inside («connect/reset» and «mode»)
|-
|RF band ||2.4 GHz
|-
|Radio transmission distance** ||Up to 50m (in open field)
|-
|Communication protocol ||IEEE 802.15.4 compatible
|-
|Number of supported alarming devices ||Up to 10 alarming devices
|}
:<nowiki>*</nowiki>The detection distance depends on the magnetic properties and construction of magnetic detacher and sensitivity settings.
:<nowiki>**</nowiki>The transmission distance depends on many factors ( the presence of the shielding structures, the mutual orientation of the devices, etc. )

===Alarming device (Control panel)===
{|border=1 cellpadding=5
|-
|Power supply ||5-12V, 0.5A (from external power adapter)
|-
|Dimensions (W x H x D)||80mm x 40mm x 20mm
|-
|Color ||Black
|-
|Mounting ||Using double-sided adhesive tape
|-
|Indication ||Audible (alarm), LED (alarm zone number)
|-
|Controls ||2 buttons on the front panel ("connect/reset" and "alarm mode")
|-
|RF band ||2.4 GHz
|-
|Communication protocol ||IEEE 802.15.4 compatible
|-
|Number of supported sensors ||Up to 10 sensors
|}
Limitations on usage:
:- Installation of sensors is not closer than 1m from moving metal objects;
:- Installation of sensors is not closer than 0.5m from the power wiring and acousto-magnetic anti theft systems;
:- Installation of the system is not closer than 50m from the metro lines and electric trains, not closer than 20m from the transformer substations and high tension power distribution lines.

== Installation ==
* [[MagnetGuard V2 - General installation issues | General installation issues]] 
* [[MagnetGuard V2 - The Central Unit | The Central Unit]] 
* [[MagnetGuard V2 - The Sensor | The Sensor]] 
* [[MagnetGuard V2 - Initial configuration of the system | Initial configuration of the system]] 
* [[MagnetGuard V2 - Sensor Adjustment | Sensor Adjustment]] 
* [[MagnetGuard V2 - Installation procedure | Installation procedure]] 

== How To ==
* [[How to setup Magnet detector Control panels in repeating mode]]

[[Category:Magnet detector|*]]

MagnetGuard V2 - Sensor Adjustment

2018-11-25T13:47:59Z

Monster: /* Criteria adjustment */

== Sensor Adjustment ==
=== Sensitivity adjustment ===
Sensor sensitivity provides the ability to choose the level of sensor response to magnetic field changes. It let us obtain the required detection range free of false alarms. 
Sensor sensitivity adjustment process is performed by consecutive pressing the button 2 «Sens» to choose the required sensitivity level. LED1 will be activated and LED 2 will make number of blinks which corresponds with the selected sensitivity level (refer to the table, default setting is highlighted). 
Sensitivity settings of the sensor:
{|border=1 cellpadding=5
|-
| LED2 flashes || Approx. magnetic field changes threshold, nТl || Sensitivity level
|-
| 1 || 380 || Very high
|-
| 2 || 450 || High
|-
| 3 || 500 || High (default)
|-
| 4 || 630 || High to intermediate
|-
| 5 || 900 || Intermediate
|-
| 6 || 1000 || Intermediate
|-
| 7 || 1200 || Intermediate
|-
| 8 || 1400 || Intermediate to low
|-
| 9 || 1600 || Low
|-
| 10 || 1800 || Low
|}

=== Criteria adjustment ===
Criteria adjustment let us maintain the time needed for magnetic field changes to be recognised as a detacher. This allows to eliminate false alarms caused by phones, bags with magnet locks or magnetic random noise (high current commutation) which occur mostly for a very short period of time. 
Criteria adjustment process is performed by consecutive pressing on the button 1 «Criteria» to choose the criteria settings number. LED2 will be activated and LED 1 will make number of blinks which corresponds with the selected criteria level (refer to the table, default setting is highlighted). 
Criteria settings of the sensor:
{|border=1 cellpadding=5
|-
| LED1 flashes || Approx. min. detection time / max. filter time, sec|| Criteria level
|-
| 1 || 0,02/0,2 || No filtering
|-
| 2 || 0,2/0,6 || Very high
|-
| 3 || 0,4/1,2 || High (default)
|-
| 4 || 0,6/1,5 || High to intermediate
|-
| 5 || 0,9/1,9 || Intermediate
|-
| 6 || 1,1/2,3 || Intermediate
|-
| 7 || 1,3/2,7 || Intermediate
|-
| 8 || 1,5/3,1 || Intermediate to low
|-
| 9 || 1,7/3,5 || Low
|-
| 10 || 1,9/3,9 || Low
|}

MagnetGuard V2 - Sensor Adjustment

2018-11-25T13:47:24Z

Monster: /* Sensitivity adjustment */

== Sensor Adjustment ==
=== Sensitivity adjustment ===
Sensor sensitivity provides the ability to choose the level of sensor response to magnetic field changes. It let us obtain the required detection range free of false alarms. 
Sensor sensitivity adjustment process is performed by consecutive pressing the button 2 «Sens» to choose the required sensitivity level. LED1 will be activated and LED 2 will make number of blinks which corresponds with the selected sensitivity level (refer to the table, default setting is highlighted). 
Sensitivity settings of the sensor:
{|border=1 cellpadding=5
|-
| LED2 flashes || Approx. magnetic field changes threshold, nТl || Sensitivity level
|-
| 1 || 380 || Very high
|-
| 2 || 450 || High
|-
| 3 || 500 || High (default)
|-
| 4 || 630 || High to intermediate
|-
| 5 || 900 || Intermediate
|-
| 6 || 1000 || Intermediate
|-
| 7 || 1200 || Intermediate
|-
| 8 || 1400 || Intermediate to low
|-
| 9 || 1600 || Low
|-
| 10 || 1800 || Low
|}

=== Criteria adjustment ===
Criteria adjustment let us maintain the time needed for magnetic field changes to be recognised as a detacher. This allows to eliminate false alarms caused by phones, bags with magnet locks or magnetic random noise (high current commutation) which occur mostly for a very short period of time. 
Criteria adjustment process is performed by consecutive pressing on the button 1 «Criteria» (Figure 3) to choose the criteria settings number. LED2 will be activated and LED 1 will make number of blinks which corresponds with the selected criteria level (refer to the table 3, default setting is ighlighted). 
Criteria settings of the sensor:
{|border=1 cellpadding=5
|-
| LED1 flashes || Approx. min. detection time / max. filter time, sec|| Criteria level
|-
| 1 || 0,02/0,2 || No filtering
|-
| 2 || 0,2/0,6 || Very high
|-
| 3 || 0,4/1,2 || High (default)
|-
| 4 || 0,6/1,5 || High to intermediate
|-
| 5 || 0,9/1,9 || Intermediate
|-
| 6 || 1,1/2,3 || Intermediate
|-
| 7 || 1,3/2,7 || Intermediate
|-
| 8 || 1,5/3,1 || Intermediate to low
|-
| 9 || 1,7/3,5 || Low
|-
| 10 || 1,9/3,9 || Low
|}

MagnetGuard V2 - The Sensor

2018-11-25T13:45:49Z

Monster: /* The sensor */

== The sensor ==
[[File:Magnetguard v2 sensor 1.png|600px|center|Sensor]]
To '''turn on''' the sensor insert the battery. Both LED’s 1 and 2 will show by blinking pattern correspondent to current settings, first for sensitivity (LED2) and than for criteria (LED 1). Finally the sensor will send information: „Iam on”, „Battery status” and „Test alarm” to the central unit (if they were previously connected together). After that the sensor goes in active mode and is ready to work.

MagnetGuard V2 - General installation issues

2018-11-25T13:44:34Z

Monster: /* Installation guidelines for optimum performance */

== General installation issues ==
===Noise sources===
The list below shows possible noise sources: 
:- moving objects containing metal (sliding doors, elevators, cash machines, payment terminals, trolleys etc.) 
:- railway, trams or busy roads with heavy traffic situated very close to the shop 

===Installation guidelines for optimum performance===
:- Check the installation area for possible noise sources prior to installation.
:- Avoid any metal objects mentioned above.
:- Locate the central unit in a visible place for the shop/security staff. The distance between central unit and sensors should be less then 50 meters (depends on radio interference).
:- Choose a location for the microprocessor magnetic field sensors on a non-metallic surfaces and fix them at a height of about 1 - 1,3 meter using double-sided tape.
:- We recommend to use only one sensor pro fitting room if it is not wider than one meter.
:- Although the default settings of the sensors should work fine in most situations, it can be necessary to fine-tune the sensors for best performance in your specific environment (sensitivity and criteria adjustment).
:- Try to keep the sensor sensitivity as low as possible in order to avoid false alarms.
:- It is not necessary to get an alarm immediately during entering the fitting room as the detacher can be hidden and carried into the fitting room far away from the sensor. Alarm will be activated as soon as the thief will start to operate with the detacher to remove the hard tags - make adequate tests.
:- Don't transport the sensors with battery inside. The sensors will try to send information to the unplugged central unit permanently and will drain the battery. It is better to insert the battery directly before the installation.

[[File:Magnetguard v2 fitting room 1.png|600px|center|Fitting room installation example]]