Bidirectional pass counter v.2.1 - Revision history

Baya: /* Installation */

2017-04-13T10:21:09Z

‎Installation

Baya: /* Installation */

2017-04-13T10:20:56Z

‎Installation

Baya at 10:20, 13 April 2017

2017-04-13T10:20:02Z

Baya: /* Specifications */

2017-02-28T14:41:50Z

‎Specifications

Baya: /* WiFi Setup */

2016-12-23T00:04:46Z

‎WiFi Setup

Baya: /* Description */

2016-12-22T23:28:00Z

‎Description

Baya: /* Setting and checking the operation of the device */

2016-12-22T21:54:09Z

‎Setting and checking the operation of the device

Baya: /* You should check: */

2016-12-22T21:41:03Z

‎You should check:

Baya: /* You should check: */

2016-12-22T21:40:49Z

‎You should check:

Baya: /* Setting and checking the operation of the device */

2016-12-22T21:39:38Z

‎Setting and checking the operation of the device

@@ Line 41: / Line 41: @@
 == Installation ==
-[[File:Source.over.camera.jpg|thumb|Fig. 3. the color LED of working emitter through smartphone camera]]
+[[File:Source.over.camera.jpg|thumb|Fig. 3. the color of LED of working emitter through smartphone camera]]
 # Connect the power cords to the modules. The polarity does not matter.
 # Fix the modules on both sides of the aisle at a height of 1.20 — 1.40 meters. The receiver must be placed horizontally (to detect the direction of the input/output).

@@ Line 41: / Line 41: @@
 == Installation ==
-[[File:Source.over.camera.jpg|thumb|Fig. 3. LED of working emitter]]
+[[File:Source.over.camera.jpg|thumb|Fig. 3. the color LED of working emitter through smartphone camera]]
 # Connect the power cords to the modules. The polarity does not matter.
 # Fix the modules on both sides of the aisle at a height of 1.20 — 1.40 meters. The receiver must be placed horizontally (to detect the direction of the input/output).

@@ Line 41: / Line 41: @@
 == Installation ==
 # Connect the power cords to the modules. The polarity does not matter.
 # Fix the modules on both sides of the aisle at a height of 1.20 — 1.40 meters. The receiver must be placed horizontally (to detect the direction of the input/output).
 # Connect the power supply. All LEDs on the receiver should light up for 2 seconds.
 # The efficiency of the emitter can be checked by using the smart-phone camera. When you look on the emitter LED from a short distance (couple of centimeters) through the smart-phone camera, LED of working emitter will be of red-blue/purple color (Fig. 3).
 === Receiver LEDs flashing description:===

@@ Line 33: / Line 33: @@
 | Operating temperature range || 5°C — 40°C, with relative humidity of 80%
 |-
-| Dimensions (WxHxD) || 80mm x 40mm x 20mm
+| Dimensions (W x H x D) || 80mm x 40mm x 20mm
 |-
 | Hull material || ABS plastic

@@ Line 72: / Line 72: @@
 == WiFi Setup ==
-All Baozam devices use the same [[WiFi Setup]] procedure. The difference is in where the setup button is placed and how it looks. The counter ''WiFi setup'' button is inside the ''WiFi setup'' hole under the three colored LEDs on the front of the receiver (Fig. 1 top).
+All Baozam devices use the same [[WiFi Setup]] procedure. The difference is in where the setup button is placed and how it looks. The counter ''WiFi setup'' button is inside the ''WiFi setup'' hole above the three colored LEDs on the front of the receiver (Fig. 1 top).
 * [[WiFi Setup|Common Baozam device WiFi setup procedure]]

@@ Line 3: / Line 3: @@
 * receiver - with three LEDs in the middle of the front panel, the ''WiFi setup'' hole above the three LEDs and two holes on the sides of the front panel (Fig. 1 top).
 * emitter - with one LED in the middle of the front panel (Fig. 1 bottom).
-Both units have a rectangular hole for the power cord at bottom (Fig. 2). White boxes on pictures are power cord connectors.
+Both units have a rectangular hole for the power cord at bottom (Fig. 2, rectangular recess in the bottom wall). White boxes on pictures are power cord connectors.
 <gallery widths=200>

@@ Line 75: / Line 75: @@
 * [[WiFi Setup|Common Baozam device WiFi setup procedure]]
-==Setting and checking the operation of the device==
+{{Setting and checking the operation of the counter}}
-# Go to https://baozam.net
-# In the ''Inventory'' section, click the ''Tuner'' button of the target device. You will be redirected to the device's ''Tuner'' page. The device will go into the ''Setup mode'' after the next transferring data to the cloud.
-#* <div style='font-size:90%'>The device sends the data to the cloud every five (5) minutes. The device immediately reports about cutting/opening the beam, turning on. To avoid waiting for five minutes, you can: a) cut off the beam - a message in 15 seconds, b) turn off/on the device.</div>
-#* Within maximum 5 minutes the device will come into the ''Setup mode'' you will get a message at the ''Tuner'' page, and all device parameters will be displayed.
-# Click the ''blue'' parameter to view the ''Stream & Monitor'' buttons.
-#* ''Stream'' - on/off sending this parameter to the cloud.
-#* ''Monitor'' - on/off immediate displaying parameter values in the ''Monitor'' box on the page.
-=== You should check: ===
-If the emitter beam hits the receiver sensors (parameters ''left sensor'' & ''right sensor'').
-* Turn on sensor monitors. Normal values range 5 - 6.
-* If the reading is less than 5, the emitter and receiver are not aligned or something breaks the beam. Adjust the alignment, clean the beam path.
-* If values are greater than 7 look for the source of noise.
-−
-The direction of the entrance/exit.
-* By default, the input direction is from left to right relatively to the receiver.
-* Turn on monitoring parameter ''count_in'' & ''count_out''. Cross the beam ...
-* Change the direction by using the ''Mode Control'' button. Use the drop-down button ''LEFT to RIGHT is ENTER'' or ''LEFT to RIGHT is EXIT'' to select the desired direction.
-−
-'''Important!''' If you have changed any parameter, be sure to save the changes (''Settings'' --> ''Save''). Otherwise, when you turn the device off your settings will be lost.
 == See also ==