Magnet with trolley detector configuration - Revision history

Baya: /* Adjustment of the parameters for the detection of magnets during metal compensation */

2017-04-13T07:29:08Z

‎Adjustment of the parameters for the detection of magnets during metal compensation

Baya at 07:28, 13 April 2017

2017-04-13T07:28:35Z

Baya: Created page with "== Parameter group "magnet with trolley" == The system responds to a change in the magnetic field in the sensor's operating range. At the same time, the activation of the magn..."

2017-04-13T07:21:28Z

Created page with "== Parameter group "magnet with trolley" == The system responds to a change in the magnetic field in the sensor's operating range. At the same time, the activation of the magn..."

New page

== Parameter group "magnet with trolley" ==
The system responds to a change in the magnetic field in the sensor's operating range.
At the same time, the activation of the magnet is blocked if the metal is simultaneously detected.
These functions are intended for detecting magnets when used on an object (for example, cash registers of hypermarkets), in the area of operation of a system of trolleys with an iron structure, since iron has the properties of a magnet.

These parameter groups allow you to adjust the detection of magnets during metal compensation.
* '''dV''' - the overall response of the system to the magnetic field with metal compensation
* '''th''' - sensitivity detection setting. The parameter values are selected based on the noise level (0.25 ... 10.0)
* '''K-magnet-2''' - the parameter of taking into account the rate of change of the magnetic field
* '''K-metal''', '''K-metal-2''' - the parameters of accounting for changes and the rate of change during the movement of the metal
* '''Buf size (magnet-2)''' - the size of the history buffer (5 - corresponds to 0.05 sec) for the analysis of changes in the magnetic field
* '''Buf size (metal-2)''' - the size of the history buffer (10 - corresponds to 0.1 sec) for analysis of changes during the movement of metal
* '''th in delay''' / '''th out delay''' - time setting for detection when dV is exceeded above th and at detection loss at dV is less than th
* '''delta_i''' - the indicator variable of the changes during the movement of the metal
* '''delta_m''' - indicator variable of magnetic field changes
* '''state''' - the state of detection of the magnet with trolley
* '''counter''' - the the lifetime magnet events counter.

Figure 1 shows an example of the change in the state of the detection of a magnet (state) in time, depending on the indicator value ('''''dV''''') and the influence of the tuning parameters ('''''th, th in delay, th out delay''''').

@@ Line 22: / Line 22: @@
 == Adjustment of the parameters for the detection of magnets during metal compensation ==
 . The settings of this functionality assumes that the metal detector and magnet detector A (''magnet-A'') were previously set up and operate.
 . To estimate the level of the magnet's influence, use the variable '''''dV''''', which should be included in the monitoring mode.
@@ Line 30: / Line 31: @@
 After the settings, save the settings.
 . If it is necessary to adjust the metal compensation when transporting the trolley, the parameters '''''K-metal''''', '''''K-metal-2''''', '''''buf size (metal-2)''''' are selected so that the system does not react to the magnetic field of the trolley when it moves.
@@ Line 39: / Line 41: @@
 After the settings, save the settings.
 . The device can send information about the number of saves of the magnet detector over the period or the message about the operation based on the counter and state variables to account for the statistics of the alarms and synchronization with the video surveillance systems.

@@ Line 1: / Line 1: @@
 == Parameter group "magnet with trolley" ==
 The system responds to a change in the magnetic field in the sensor's operating range.
 At the same time, the activation of the magnet is blocked if the metal is simultaneously detected.
@@ Line 18: / Line 19: @@
 Figure 1 shows an example of the change in the state of the detection of a magnet (state) in time, depending on the indicator value ('''''dV''''') and the influence of the tuning parameters ('''''th, th in delay, th out delay''''').