Bidirectional pass counter v.1.x

Description

The counter consists of two modules:

• emitter - with one LED in the middle of the front panel (Fig. 1).
• receiver - module with LED in the middle of the front panel and two holes on the edges of the front panel (Fig. 2). Also on this module top you can find a narrow hole to access the button to activate the WiFi setting mode (Fig. 3).

Both units have a rectangular hole for the power cord at bottom side (Fig. 4).

• 

  Fig. 1. Emitter

• 

  Fig. 2. Receiver

• 

  Fig. 3. Receiver. Top view

• 

  Fig. 4. Bottom view

Specifications

Maximum distance between emitter and receiver	6 meters
IR wavelength	940 nm
Modulation frequency of the IR signal	38 kHz
Power supply	5 — 24 V DC
Communication standard	802.11b/g/n (WiFi) network with a password only
Used communication protocols	TCP / IP, TLS 1.2, HTTPS, WebSocket
Power Consumption
emitter	no more than 100 mW
receiver	1 W
Operating temperature range	0°C — 40°C, with relative humidity of 80%
Dimensions (WxHxD)	80mm x 40mm x 20mm
Material hull	ABS plastic
Color	grey, black

Installation

1. Connect the power cords to the modules. If you connect the emitter power is necessary to observe the polarity ( "+" - near the wall, Fig. 5).
2. Fix the modules on both sides of the aisle at a height of 1.20 — 1.40 meters. The receiver must be placed horizontally (to account for the direction of the input/output).
3. Connect the power supply.
4. The efficiency of the emitter can be checked using the smartphone camera. When viewed from the front side on the emitter LED from a short distance through the smartphone's camera, LED of running emitter will be painted in red-blue/purple color (Fig. 6).
5. Receiver LED will flashing red and/or green in the different modes:
   • Normal: the green every 5 seconds and/or at the intersection of the beam visitor;
   • Setup mode: the green 10 Hz;
   • Overlap beam: frequent blinking red (~ 10 Hz). The mode is set when there is no signal from the transmitter for 25 seconds;
   • There is no WiFi network: the red every 5 seconds.

• 

  Fig. 5. Emitter. The polarity of the connection

• 

  Fig. 6. LED of working emitter

WiFi Setup

All Baozam devices use the same WiFi Setup procedure. The difference is in where the setup button is placed and how it looks. The counter WiFi setup button is inside the narrow hole at the top of the receiver (Fig. 3). Button should be pressed with a toothpick. Sometimes an angle. When you press the button you feel (not hear) a click.

• Common Baozam device WiFi setup procedure

Setting and checking the operation of the device

1. Go to https://baozam.net
2. In the Inventory section, click the Tuner button of the target device. You will be redirected to the device's Tuner page. The device will go into the Setup mode after the next transferring data to the cloud.
   • The device sends the data to the cloud every five (5) minutes. The device immediately reports about cutting/opening the beam, turning on. To avoid waiting for five minutes, you can: a) cut off the beam - a message in 15 seconds, b) turn off/on the device.
   • Within maximum 5 minutes the device will come into the Setup mode you will get a message at the Tuner page, and all device parameters will be displayed.
3. Click the blue parameter to view the Stream & Monitor buttons.
   • Stream - on/off sending this parameter to the cloud.
   • Monitor - on/off immediate displaying parameter values in the Monitor box on the page.

You should check:

If the emitter beam hits the receiver sensors (parameters left sensor & right sensor).

• Turn on sensor monitors. Normal values ​​range 5 - 6.
• If the reading is less than 5, the emitter and receiver are not aligned or something breaks the beam. Adjust the alignment, clean the beam path.
• If values are ​​greater than 7 look for the source of noise.

The direction of the entrance/exit.

• By default, the input direction is from left to right relatively to the receiver.
• Turn on monitoring parameter count_in & count_out. Cross the beam ...
• Change the direction by using the Mode Control button. Use the drop-down button LEFT to RIGHT is ENTER or LEFT to RIGHT is EXIT to select the desired direction.

Important! If you have changed any parameter, be sure to save the changes (Settings --> Save). Otherwise, when you turn the device off your settings will be lost.

See also

• Bidirectional pass counter v.2.1